Services

A cooktop installation is as much about the countertop cutout as the appliance itself — the unit has to seat flush and level in an existing or new cutout, seal cleanly against spills, and connect safely to either a dedicated gas line or a 240V electric circuit. Get any of that wrong and you're looking at a wobbly cooktop, a gas leak risk, or water damage to the cabinet below from a bad seal.

Our certified crew handles the full install: fitting the unit to the cutout, running and testing the gas or electric connection to code, sealing the perimeter, and firing every burner before we call the job done.

• Cutout fit-check and adjustment
• Gas line or 240V electric hookup to code
• Full perimeter seal against spills
• Every burner tested before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Dishwasher installation looks simple until you're the one dealing with a water line that doesn't match your shutoff, a drain that back-feeds into the disposal wrong, or a unit that's a half-inch too tight for the cabinet opening. Any one of those turns a same-day install into a leak, a return trip, or water damage under the cabinet.

Our certified installers connect the water supply line, the drain (routed correctly to avoid siphon-back), and the power, then level the unit for quiet operation and run a full test cycle before we consider the job finished.

• Water supply line connected and leak-checked
• Drain line routed and looped correctly
• Power hookup (hardwired or plug-in, per code)
• Leveled for quiet running, full test cycle run

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

An electric dryer needs more than plugging in a cord — the vent run has to move air efficiently (a crushed or overly long duct run is the number-one cause of dryers that take three cycles to dry a load), the unit has to sit level so it doesn't walk or vibrate, and the power connection has to match your outlet type and amperage safely.

Our certified crew connects the power, routes and secures the venting, levels the unit, and runs a full test cycle to confirm it's heating and drying properly before we leave.

• Power connection matched to your outlet/amperage
• Vent routed, secured, and checked for airflow
• Unit leveled to prevent walking and noise
• Full test cycle run before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own home. That's the AKK standard: professional, dependable, and done right the first time.

Gas dryers add a real safety layer on top of everything an electric dryer needs — a certified gas line connection, a leak check, and proper venting, since a poor gas connection is a hazard, not just an inconvenience. This isn't a job for guesswork or a mismatched fitting.

Our certified crew connects the gas line to code, pressure- and leak-tests the connection, hooks up and secures the venting, levels the unit, and runs a full test cycle before we leave.

• Certified gas line connection, leak-tested
• Vent routed, secured, and checked for airflow
• Unit leveled to prevent walking and noise
• Full test cycle run before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own home. That's the AKK standard: professional, dependable, and done right the first time.

A stacked or combo washer/dryer unit is deceptively heavy and unforgiving of an uneven floor — get the leveling wrong and you'll feel it through the whole laundry room on spin cycle. And because it's two appliances in one footprint, there's twice the hookups to get right: water, drain, power, and venting, all in a tighter space than a standard side-by-side pair.

Our certified crew connects both the washer and dryer sides — water, drain, power, and venting — carefully levels the combined unit given its weight, and runs a full test cycle on both functions before we leave.

• Washer side: water supply, drain, and level
• Dryer side: power, venting, and level
• Combined unit leveled for the added weight
• Full test cycle run on both washer and dryer

Every installation is licensed, insured, and treated with the same care we'd want in our own home. That's the AKK standard: professional, dependable, and done right the first time.

Built-in microwaves rely entirely on a proper trim kit fit and a secure mount — there's no countertop or shelf holding the unit up, just the cabinetry around it. A loose or improperly shimmed install is a safety issue as much as a cosmetic one over time.

Our certified crew fits the unit and trim kit to the cutout, secures it firmly to the surrounding cabinetry, wires in the power connection, and tests every function before we leave.

• Trim kit and unit fit to the cabinet cutout
• Secure mount to surrounding cabinetry
• Power connection wired in to code
• Full function test before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Drawer microwaves install underneath the counter, which means a precise fit against the surrounding cabinetry and a slide mechanism that has to glide smoothly under real weight, load after load, for years. A cutout that's slightly off or a rail that isn't secured square is the difference between a drawer that opens like new and one that binds within a month.

Our certified crew fits and secures the unit to the cutout, checks and adjusts the drawer's slide action, wires in the power connection, and tests it fully before we leave.

• Precise fit to the under-counter cutout
• Drawer slide mechanism checked and adjusted
• Power connection wired in to code
• Full function test before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

An over-the-range microwave has to do three jobs at once: mount securely above a working cooktop, vent properly so it's actually pulling steam and smoke instead of just recirculating it uselessly, and stay wired in safely despite the heat below it. Mounting brackets that aren't anchored into real structure are a real hazard directly over where you cook.

Our certified crew mounts the unit to the cabinet or wall bracket, connects and routes the venting, wires in the power connection, and tests the fan, light, and microwave functions before the job is done.

• Secure mount to cabinet or wall bracket, anchored properly
• Venting connected and routed (ducted or recirculating)
• Power wired in to code
• Fan, light, and microwave functions all tested

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

A 48-inch-or-larger pro range is a different kind of install than a standard range — these units are significantly heavier, have a wider footprint that needs precise clearance from cabinetry, and run dual fuel (gas burners, electric oven), meaning two separate connections both have to be done right. Skimping on clearance or the gas connection on a unit this size isn't a small mistake.

Our certified crew handles the dedicated gas line and the electric oven connection to code, carefully levels the unit given its size and weight, confirms proper clearance, and tests every burner and both the oven and any convection function before the job is done.

• Dedicated gas line connection, leak-tested
• Electric oven circuit connected to code
• Precision leveling for the unit's full weight and footprint
• Every burner, the oven, and convection function tested

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Pro-style dual-fuel ranges pack gas burners and an electric oven into one unit, which means a dedicated gas line, a proper 240V electric connection for the oven, and careful leveling given how much these units weigh compared to a standard range. Get the gas connection or the leveling wrong and you're either looking at a safety issue or a range that rocks under a heavy pot.

Our certified crew handles both the gas and electric connections to code, levels the unit precisely, and tests every burner and the oven — including convection, if equipped — before the job is done.

• Dedicated gas line connection, leak-tested
• Electric oven circuit connected to code
• Precision leveling for the unit's weight
• Every burner and oven function tested

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Range hoods need a secure wall or cabinet mount, ducting connected correctly (or a proper recirculating filter setup if you're not venting outside), and a wired-in fan and light that both actually work — not just spin. A hood mounted slightly off can vibrate loose over time right above your cooktop.

Our certified crew mounts the unit securely, connects the venting (ducted or recirculating), wires in the fan and lighting, and tests both before the job is done.

• Secure wall or cabinet mount
• Ducted venting or recirculating filter setup connected
• Fan and lighting wired in and tested
• Level, vibration-free mount confirmed

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Once a range hood passes 36 inches, the job changes — these units are heavier, often need reinforced mounting to hold their weight safely overhead, and move enough air that the ducting has to be sized and routed correctly or you'll lose most of the hood's actual performance. A hood that's improperly secured over a cooktop isn't something to leave to chance.

Our certified crew reinforces the mount as needed for the unit's weight, secures it in place, connects and routes the higher-capacity venting, and tests the fan speeds and lighting before the job is done.

• Reinforced mounting for the unit's weight
• Higher-capacity venting connected and routed
• Fan speeds and lighting fully tested
• Secure, level mount confirmed before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Even a standard range install has real failure points: a connection that's not secured to code, a unit that rocks slightly on one burner because it isn't level, or a slide-in range that isn't seated tight against the counter, leaving a gap where spills fall through. None of it shows up as a problem until you're already using it.

Our certified crew connects the power or gas line to code, levels the unit so nothing rocks, seats slide-in models tight against the counter, and tests every burner and the oven before we leave.

• Power or gas connection to code
• Precision leveling — no rocking on any burner
• Slide-in models seated tight against the counter
• Every burner and the oven tested

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Built-in refrigerators demand precision most freestanding units don't — the unit has to sit flush with the surrounding cabinetry, vent properly around the compressor despite the tighter enclosed space, and seal tight so the door doesn't sweat or leak cold air. A trim fit that's even slightly off is visible every time you walk into the kitchen.

Our certified crew connects the water line for the icemaker and dispenser, dials in the leveling and trim fit for a flush look, verifies proper venting, and confirms it's cooling correctly before the job is complete.

• Water line connected for icemaker and dispenser
• Flush trim fit against surrounding cabinetry
• Ventilation clearance verified for the compressor
• Confirmed cooling properly before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Larger built-in refrigerators are one of the most demanding installs in a kitchen — more weight to level precisely, more surrounding cabinetry and trim to fit around exactly, and more clearance required for proper airflow around the compressor, since these units run continuously for years and need to breathe. Get the venting wrong and the unit works harder and shorter.

Our certified crew connects the water line for the icemaker and dispenser, dials in the leveling and trim fit against the surrounding cabinetry, verifies proper venting clearance, and confirms it's cooling correctly before the job is complete.

• Water line connected for icemaker and dispenser
• Precision leveling and flush trim fit
• Ventilation clearance verified for the compressor
• Confirmed cooling properly before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Column refrigeration, panel-ready units, and premium brands like Sub-Zero and Thermador are custom to your kitchen by design — every one of these installs is different depending on your cabinetry, panel specs, and layout, which is exactly why this is quoted after we've actually seen the space, not priced off a generic checklist.

We walk through your kitchen before we quote it: confirming panel dimensions and hinge specs, checking clearance and ventilation requirements for the specific unit, and mapping out water line and power needs — so the price and the plan are both right from the start, and the install goes smoothly on day one.

• On-site walkthrough before any quote is given
• Panel and hinge specs confirmed against your cabinetry
• Water line and power requirements mapped out in advance
• Ventilation and clearance verified for the specific unit

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Setting up a new freestanding refrigerator right means more than rolling it into place — it needs to be plumbed correctly for the icemaker and water dispenser, leveled precisely on the floor so both doors seal tight and swing evenly, and confirmed cooling before anyone starts loading groceries into it.

Our certified crew connects the water line, levels the unit for a tight door seal on both sides, and confirms it's running and holding temperature before the job is done.

• Water line connected for icemaker and dispenser
• Leveled for a tight seal on both doors
• Old unit disconnected and moved out, if applicable
• Confirmed running and cooling before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Wine coolers and beverage centers live in a tight footprint under the counter, which means the fit has to be precise, the ventilation clearance around the compressor has to be respected (skip this and the unit overworks itself and runs hot), and the unit has to sit level for the door to seal properly. A door that doesn't seal tight is a slow, invisible way to lose cooling efficiency.

Our certified crew handles the power and any water hookup, dials in the precise fit and leveling for a proper door seal, confirms the ventilation clearance is correct, and verifies it's running and holding temperature before we leave.

• Precise under-counter fit with proper ventilation clearance
• Power and water hookup (if equipped) connected
• Leveled for a tight door seal
• Confirmed running and holding temperature

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

A combo wall oven — a full oven paired with a microwave or speed oven in one cutout — needs a precise fit for two separate appliances sharing one footprint, plus each function tested on its own since a fault in one doesn't always show up until you're relying on it mid-meal. Getting the cutout and power connection right the first time matters more here than on a single unit.

Our certified crew secures the combo unit in its cutout, connects the power to code, and tests every function — oven, microwave or speed oven, and any convection or special modes — independently before we leave.

• Precise fit for the combo unit's cutout
• Power connection to code for both functions
• Each function (oven + microwave/speed oven) tested independently
• Secure, flush mount confirmed

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

Double wall ovens are one of the heavier built-in installs in a kitchen — two full ovens sharing a single tall cutout, each needing its own careful test since a problem with the lower cavity can be easy to miss if you only check the top. The extra weight also means the cutout fit and mounting have to be exact, or the unit won't sit flush over time.

Our certified crew secures the unit in the cutout, connects the power to code, and tests both ovens — including any convection settings — independently before the job is done.

• Precise fit for the tall double-cavity cutout
• Power connection to code, sized for both ovens
• Both cavities tested independently, including convection
• Secure, flush mount confirmed given the added weight

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

A wall oven has to sit perfectly flush in its cabinet cutout — even a small gap looks wrong permanently, and a poor seal around the unit lets heat and grease creep into the surrounding cabinetry over years of use. The power connection matters just as much: a wall oven draws serious amperage, and it needs to be wired to code, not just plugged in.

Our certified crew secures the unit flush in the cutout, connects the power to code, and runs a full test cycle — including any convection or special functions — before we call the job done.

• Flush, gap-free fit in the cabinet cutout
• Power connection wired to code
• Full test cycle, including convection/special functions
• Secure mount confirmed before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own kitchen. That's the AKK standard: professional, dependable, and done right the first time.

A washer that isn't level doesn't just make noise — it walks across the floor during spin cycle, wears out its own suspension early, and can eventually damage the floor or the hoses behind it. The supply and drain connections matter just as much: a loose hose or a poorly routed drain is the most common cause of a laundry-room flood.

Our certified crew connects the water supply and drain lines, levels the unit precisely so it runs quiet and stays put, and runs a full test cycle before we call the job done.

• Hot and cold water supply lines connected and leak-checked
• Drain line routed and secured
• Precision leveling for quiet, stable operation
• Full test cycle run before we leave

Every installation is licensed, insured, and treated with the same care we'd want in our own home. That's the AKK standard: professional, dependable, and done right the first time.